Error Code 0X80070035 | Solutions to Fix the Error

Error code 0x80070035, commonly accompanied by the message “The network path was not found,” is a frequent Windows error. It typically occurs when your computer cannot connect to or access a shared folder, network drive, or another device on your network.

Here are the common causes and fixes for this error:

Common Causes of Error 0x80070035:

1. Network Path Issues: The target computer or shared folder might be unavailable or disconnected.

2. Firewall or Antivirus Block: Firewalls or security software might block the connection.

3. Incorrect Network Settings: Misconfigured network settings, such as IP addresses or DNS settings, can cause this error.

4. File Sharing Disabled: File and printer sharing might be turned off.

5. Network Discovery Disabled: Your computer might not be able to see other computers on the network.

Also Read : Thewackywatch com Vote

How to Fix Error Code 0x80070035:

1. Check the Network Connection

• Make sure both computers are connected to the same network.

• Test if the target computer is reachable by pinging it. Open Command Prompt (type cmd in the Start menu and hit Enter), then type:

  ping [target-computer-IP-address]


  • If it doesn’t respond, the target computer may be down or disconnected from the network.

2. Enable Network Discovery and File Sharing

• Network Discovery and File Sharing should be enabled on both computers.

  • Go to Control Panel > Network and Sharing Center > Change advanced sharing settings.

  • Turn on Network Discovery and File and Printer Sharing.

  • Save changes.

3. Disable Windows Firewall Temporarily

• Firewalls can block the connection. Disable your firewall temporarily to test if it’s causing the issue.

  • Open Control Panel > System and Security > Windows Defender Firewall.

  • Click Turn Windows Firewall on or off, then choose Turn off Windows Firewall.

  • If this resolves the issue, you might need to configure your firewall to allow file sharing.

4. Check TCP/IP Settings

• Resetting TCP/IP settings can sometimes resolve connectivity issues.

  • Open Command Prompt as an administrator (Right-click and choose Run as administrator).

  • Type the following command and hit Enter:

    netsh int ip reset


  • Restart your computer.

5. Re-map Network Drive (if applicable)

• If you’re accessing a shared folder or network drive, try disconnecting and re-mapping the drive.

  • Open File Explorer > Right-click on This PC > Map network drive.

  • Enter the correct path to the shared folder and make sure the box for Reconnect at sign-in is checked.

6. Check DNS Settings

• Ensure that the DNS server settings are correctly configured. You may want to use Google’s DNS servers (8.8.8.8 and 8.8.4.4).

  • Go to Control Panel > Network and Sharing Center > Change adapter settings.

  • Right-click your network connection > Properties.

  • Select Internet Protocol Version 4 (TCP/IPv4) > Use the following DNS server addresses:

    • Preferred DNS: 8.8.8.8

    • Alternate DNS: 8.8.4.4

  • Save and restart.

7. Update or Roll Back Network Adapter Driver

• An outdated or corrupted network adapter driver can cause issues with connecting to network paths.

  • Go to Device Manager (press Win + X and select Device Manager).

  • Expand Network adapters > Right-click on your adapter > Update driver.

  • You can also try rolling back the driver if it started after a recent update.

8. Ensure the Network Sharing Service is Running

• The Server and Workstation services are essential for network sharing.

  • Press Win + R, type services.msc, and hit Enter.

  • Ensure that the following services are Running:

    • Server

    • Workstation

    • TCP/IP NetBIOS Helper

  • If they aren’t running, right-click and select Start.

Final Thoughts:

This error typically points to a network or sharing issue between computers. Following the steps above should help you resolve it. If none of the solutions work, you may want to check for Windows Updates or even reinstall your network drivers.