| Infrared
Curing and Convection Curing |
INTRODUCTION Infrared Curing and Convection Curing
The
coatings and paint industries strive to provide high technology coatings while
reducing volatile organic compounds and energy consumption to produce a finished
coating. Conventionally Convection ovens are used to cure the coatings. But this
process which uses electric heaters is not an optimal process and is associated
with various disadvantages. Improved technologies are available today, which can
either replace or improve the convection curing process. Infrared Curing is such
a technology which uses Infrared rays emitted by an Infrared emitter to provide
the required cure. Infrared curing applies light energy to the part surface by
direct transmission from an emitter. Some of the energy emitted will be reflected
off the surface, some is absorbed into the polymer and some is transmitted into
the substrate. This direct transfer of energy creates an immediate reaction in
the polymer and cross linking begins quickly once the surface is exposed to the
emitter. Infrared emitters are often custom manufactured to suit the production
demand. The various aspects of Infrared curing and convection curing and the possibility
of combining these two technologies into a singe system will be discussed in this
seminar.
CURING
Curing is a process of baking surface coatings so as to dry them up quickly.
Curing is a broad term which means all the techniques employed for the finishing
operations incurred during part production. Curing essentially involves either
the melting of the coating or evaporation of volatile fluids present in the coating
by the application of heat energy.
Curing is given to a wide range of materials both organic and inorganic .Usually
curing is given to materials like , "
Paints
" Enamel
" Laquer
" Powder coatings
" Varnishes
"
Epoxy coatings
" Acrylic coatings
" Primers Etc
Curing is also given to Rubber and Latex .The principle used for curing can also
be used for drying rice and grains.
CONVECTION
CURING Convection
ovens are usually used for curing purposes. Traditional convection ovens use heated
forced air to provide the necessary cure. Convection ovens consist of a chamber
lined on the inside with Electric heaters. The shape of the chamber will be in
accordance to the shape or geometry of the part being cured. A series of blowers
circulate the heated air around providing the required cure. This process depends
on convection to transfer heat from hot air to body surface and conduction to
transfer heat to the interior of the surface. The air being delivered is held
at temperature using closed-loop control, which provides predictable, repeatable
results. Typically a temperature of around 250-500 degree farenheit is required
for paint or powder. Though convection ovens are widely used today they have certain
disadvantages, which chokes the overall productivity of a company
Disadvantages
of convection ovens :
"
Fairly long heating times:-
Convection is a slow process. It takes a considerable
amount of time for the heaters to heat up and raise the temperature of air to
the required level. This causes a lag in the process and hence the curing time
increases. Longer curing time spells reduced assembly line movement. This in turn
reduces productivity. "
High energy consumption:-
A convection column dryer uses around 2000 BTU(British
Thermal Unit) of energy to remove 1 pound of moisture. They use around 7.7 KW
of electrical energy to dry a ton of rice. These are significantly larger figures
for any company trying to bring energy consumption under control. The additional
use of blowers and compressors further increases energy consumption. "
Large floor area required:-
Convection ovens are bulky in nature. Due to the
presence of compressors and blowers, additional space is needed, which in turn
increases the floor area requirement. "
Air circulation is required:-
Convection heating requires a medium for transmission
of heat. Hence blowers are employed for good circulation of heated air. This increases
the overall cost of the equipment.
See Full Report
You may also like this : Dyna-cam engine, Apache Helicopter, CAMM Systems, Friction Stir Welding, HEMI engines, Just In Time Manufacturing, Lean manufacturing, Quality improvement tool "poka yoke", MEMS for Space, Personal Protection , Mine Detection Using Radar Bullets, Overall Equipment Effectiveness, Predictive Maintenance using Thermal Imaging, Methanol Fueled Marine Diesel Engine, Quality function deployment, Quasi turbine, Robots In Radioactive Environments, Sidewinder Missile, Smart Materials, Transit Mixer & Concrete Pump, Turbofan Engine, Solar Sails, Ultrasonic Metal Welding, The Hy-Wire Car, Thermal Barrier Coatings, Ultrasonic Techniques for hidden corrosion detection, Solar-powered vehicles , Two Stroke Engine Using Reed Valves, Vacuum Braking System, Variable Valve Timing In I.C. Engines, Space Elevator, Supercavitation, Thermal shock on interfacial adhesion of thermally conditioned, Total Productive Maintenance, Welding Robots , Air powered cars, Biomechatronic Hand , Computer Aided Process Planning , Re-entry of Space Vehicle, Sensotronic Brake Control, Skid Steer Loader and Multiterrain Loader, Space Robotics, Space Shuttles and its Advancements, Continuously variable transmission (CVT),Cryogenic grinding, Design, Analysis, Fabrication And Testing Of A Composite Leaf Spring, F1 Track Design and Safety, Green Engine, Head And Neck Support (HANS), Hydro Drive,Mechanical Seminar Reports, PPT and PDF.
|
<<back |
