Page 1 of 1

CRDI Engines

PostPosted: Fri Sep 20, 2013 6:47 am
by Prasanth
Older engines make use of a mechanical fuel pump and valve assembly which is driven by the engine crankshaft, usually via the timing belt or chain. These engines use simple injectors which are basically very precise spring-loaded valves which will open and close at a specific fuel pressure. The pump assembly consists of a pump which pressurizes the fuel, and a disc-shaped valve which rotates at half crankshaft speed. The valve has a single aperture to the pressurized fuel on one side, and one aperture for each injector on the other. As the engine turns the valve discs will line up and deliver a burst of pressurized fuel to the injector at the cylinder about to enter its power stroke. The injector valve is forced open by the fuel pressure and the diesel is injected until the valve rotates out of alignment and the fuel pressure to that injector is cut off. Engine speed is controlled by a third disc, which rotates only a few degrees and is controlled by the throttle lever. This disc alters the width of the aperture through which the fuel passes, and therefore how long the injectors are held open before the fuel supply is cut, controlling the amount of fuel injected.

This contrasts with the more modern method of having a separate fuel pump (or set of pumps) which supplies fuel constantly at high pressure to each injector. Each injector then has a solenoid which is operated by an electronic control unit, which enables more accurate control of injector opening times depending on other control conditions such as engine speed and loading, resulting in better engine performance and fuel economy. This design is also mechanically simpler than the combined pump and valve design, making it generally more reliable, and less noisy, than its mechanical counterpart.

Both mechanical and electronic injection systems can be used in either direct or indirect injection configurations.


CRDI stands for Common Rail Direct Injection meaning, direct injection of the fuel into the cylinders of a diesel engine via a single, common line, called the common rail which is connected to all the fuel injectors.

Whereas ordinary diesel direct fuel-injection systems have to build up pressure anew for each and every injection cycle, the new common rail (line) engines maintain constant pressure regardless of the injection sequence. This pressure then remains permanently available throughout the fuel line. The engine's electronic timing regulates injection pressure according to engine speed and load. The electronic control unit (ECU) modifies injection pressure precisely and as needed, based on data obtained from sensors on the cam and crankshafts. In other words, compression and injection occur independently of each other. This technique allows fuel to be injected as needed, saving fuel and lowering emissions.

More accurately measured and timed mixture spray in the combustion chamber significantly reducing unburned fuel gives CRDi the potential to meet future emission guidelines such as Euro V. CRDi engines are now being used in almost all Mercedes-Benz, Toyota, Hyundai, Ford and many other diesel automobiles.

The start of combustion (SOC) in the combustion chamber has a considerable influence upon all performances of the engine. In this paper, cylinder pressure was investigated as a means for the closed-loop SOC control of a common-rail direct injection (CRDI) diesel engine. In order to detect the SOC, the crank angle position where the difference pressure became 10 bar was selected as the pressure variable. Using this pressure variable as a feedback variable, an adaptive feed forward control was proposed. The feed forward controller consisted of the radial basis function network (RBFN) and the feedback error learning method, which was used for the training of the network. The proposed SOC control strategy showed a far better regulation performance than that of the linear feedback controller. A further extension of the strategy based on the individual cylinder pressure feedback, the individual cylinder SOC control strategy, effectively reduced cylinder-by-cylinder SOC variation in steady and transient engine operations

Re: CRDI Engines

PostPosted: Fri Feb 14, 2014 2:37 pm
by chandana28
pls send me crdi engine ppt and report

Re: CRDI Engines

PostPosted: Tue Mar 25, 2014 8:05 am
by sasidhar19992
sir plz send me ppt and report of CRDI ENGINES

Re: CRDI Engines

PostPosted: Thu Apr 10, 2014 5:54 am
by pavanshivaraj
sir plz send me ppt and report of CRDI ENGINES

Re: CRDI Engines

PostPosted: Tue Jul 01, 2014 3:21 pm
by anoop0035
pls send me crdi seminar report and ppt